littleBits Sequencer

$72.68

ex GST ($79.95 inc GST)

Tags:

Circuits littleBits littleBits Input Making & Tinkering STEAM Products

Description

The sequencer allows you to connect up to eight outputs and control them in sequential patterns. Sequences that would take as long as 4 days to program without littleBits will only take you seconds!

Automatically cycle through the entire sequence
Control the speed of the sequence using dimmers or sensors
Run the sequence four ways: forwards, backwards, pendulum, or random
Swap automation for full control and step through each part of the sequence using a button, sound trigger, or any other high signal input

There are two clock modes that control when the module transitions from sequence step to sequence step. In “step” mode the sequence transitions to a new sequence step on input low-to-high transitions. In this mode, the clock output is high when the input is above 2.5V, and the clock output is low when the input is below 2.5V.

In “speed” mode the sequence transitions to a new sequence step at a fixed frequency. The step frequency is proportional to the voltage at the input. At 0V input, the frequency is 0Hz (the sequencer does not step). At 5 volts the step frequency is approximately 80Hz. In this mode, the clock output is a square waveform at the step frequency The four sequence modes control the order in which the 8 sequenced outputs are activated. At any given time, there is exactly one of the 8 sequenced outputs set to 5V. All other outputs are set to 0V.

“Forward” mode sets output 1 to 5V, then on the next step output 2 is set to 5V, and so on. After activating each output in turn, the sequence then continuously repeats, starting at output 1.

“Backwards” mode is the same as “forward” mode, except that the sequence steps from output 8 to output 1 and is set to 5V at each step.

“Pendulum” mode sets output 1 to 5V, then on the next step output 2 is set to 5V, and so on. Upon reaching output 8, the sequence reverses and steps down from 7 to 1.

“Random” mode sets a randomly selected output to 5V at each step.

UNDER THE HOOD

The input signal is buffered by an opamp (U1), then passed through a single pole RC low pass filter, then a 2-pole active low pass filter (U3). The combined filters band limit the signal to 160Hz with an 18dB per octave filter slope. This signal is split into two paths. One path leads to the Analog-to-Digital Converter (ADC) of an Atmel ATMEGA168 microcontroller (U2). The other path leads to a General Purpose Input-Output (GPIO) pin on the same microcontroller. The path to the ADC is used in “speed” mode because in speed mode, we need to precisely measure the input voltage, and the ADC is precise. The path to the GPIO pin is used in “step” mode, because we need to quickly measure the timing of an input low-to-high transition, and the GPIO pin responds very quickly to transitions. Depending on the clock mode, microcontroller converts the measured input values into either the sequencer step speed in “speed” mode, or simply goes to the next sequencer step when it detects a low-to-high transition in “step” mode. These values are translated into signals that control the pins of the microcontroller connected to the various outputs.

More from littleBits!

Kits Inputs Outputs Power Wire/Logic Accessories

littleBits At-Home Learning Starter Kit $113.59 ex GST

The littleBits At-Home Learning Starter Kit provides an easy-to-follow, flexible, and powerful solution for reinforcing STEAM learning at home. This kit is ideal for educators to send home for individualised learning and can be easily facilitated and guided by parents. Endless opportunities for invention Use this circuit kit to confidently engage kids at home with five independent or parent-guided STEAM-based inventions. Open-and-go introductory circuit kit to learn electronics Screenless learning experience; no device or coding experience required Access additional activities, curriculum guides, resources, and more in littleBits Classroom Engage individual learners with their own starter kit and turn their ideas into a reality with 5 bits and 12 accessories Recommended for ages 8+ What’s in the At-home Learning Starter Kit circuit kit for kids? Bits 1 p4 power 1 wire 1 button 1 slide dimmer 1 servo (cross axle) Accessories 1 servo mount bucket 1 mechanical arm 1 mounting board 1 battery clip 4 adhesive bitShoes 1 glue dot sheet 1 ball caster 1 9v battery 1 battery cable

littleBits STEAM+ Coding Kit - International $813.64 ex GST

Invent and code with one, easy to use kit. The littleBits STEAM+ Coding Kit contains 25 Bits, a newly designed durable storage container, printed teacher support materials and 40+ hours of standards-aligned STEAM and Coding curriculum. Compatible with the Fuse app, students can program littleBits inventions and simulate circuits to level up the learning experience. Engage up to 4 students per kit with 25 Bits and 34 accessories Run 40+ hours unplugged, cross-curricular lessons and coding tutorials available on littleBits Classroom littleBits Classroom Unit Plans, including STEAM Inventions, Coding Fundamentals, and Engineering Design, are standards-aligned (Grades 3-8) Compatible with the littleBits Fuse app, students of all coding abilities can program the codeBit through blocks or Java-Script text and level up their inventions Improved durable storage container for easy organization and clean up & printed materials for instructional support and classroom implementation NOTE: The previous square LED matrix has been replaced by a round matrix. Some images on this page may still contain the square matrix. What's in the Pack? Bits 2x buttons 1x temperature sensor 1x long LED 1x buzzer 1x cross axle servo 1x USB power 1x pressure sensor 1x speaker 1x square LED matrix 1x codeBit 1x light sensor 1x power 2x cross axle DC motors 1x pulse 1x fork 1x slide dimmer 1x fan 1x inverter 1x number 1x RGB LED 2x wires 1x bargraph Accessories 1x Rechargeable battery 2x powerSnap 1x USB cable, 1.5mm 1x USB cable, 0.5m Magnet BitShoes Hook and Loop BitShoes Twist Ties 1x 9V batteries + Cable 1x USB Power Adapter + Cable 2x wheels 3x mechanical arms 1x standard mounting board 1x XL mounting board 1x Durable Storage Carrying Case Additional accessories

littleBits STEAM+ Coding Class Pack - International $7,995.45 ex GST

The littleBits STEAM+ Class Pack is an all-in-one coding and engineering educational solution designed to inspire and engage students grades 3–8 in STEAM learning. This comprehensive kit includes 10 individualized sets with storage, a comprehensive Invention Guide, and over 40 hours of standards-aligned STEAM curriculum to fuel critical thinking, problem-solving, and teamwork through hands-on activities and projects. In the free Fuse app, students can level up the learning experience by programming littleBits inventions with the codeBit and simulating circuits. STEAM+ Class Pack Key Features ENGAGES UP TO 40 STUDENTS: The littleBits STEAM+ Class Pack is designed to engage up to 40 students, making it an ideal solution for classrooms or other educational settings. OVER 40 HOURS OF CURRICULUM: With more than 40 hours of standards-aligned STEAM lessons and activities, educators can easily integrate the littleBits STEAM+ Class Pack into their existing curriculum. Students practice their programming skills with—a virtual circuit builder and programming platform when used with the included codeBit. INNOVATIVE MODULAR DESIGN: The littleBits STEAM+ Class Pack features a unique, colour-coded modular system that allows students to explore electronics, coding, and engineering concepts in an intuitive, engaging manner. SUPPORTS COLLABORATION: The Class Pack includes 10 individual kits, each designed to support multiple students, encouraging teamwork, communication, and collaboration as students work together to create innovative solutions to challenges and projects. EASY ORGANISATION AND STORAGE: Built-in storage makes it simple to keep the littleBits components organised and portable, ensuring that students can focus on learning and exploration without the hassle of clutter or lost components. NOTE: The previous square LED matrix has been replaced by a round matrix. Some images on this page may still contain the square matrix. What's in the Pack? Bits 20x button 10x temperature sensor 10x long LED 10x buzzer 10x cross axle servo 10x USB power 20x wire 10x pressure sensor 10x speaker 10x square LED matrix 10x codeBit 10x light sensor 10x power 20x cross axle DC motor 10x pulse 10x fork 10x slide dimmer 10x fan 10x inverter 10x number 10x RGB LED 10x bargraph Accessories 10x Rechargeable batteries 20x powerSnap 10x USB cable, 1.5mm 10x USB cable, 0.5mm Magnet BitShoes Hook and Loop BitShoes Twist Ties 10x 9V batteries + Cable 10x XL mounting boards 10x USB Power Adapter + Cable 20x Wheels 30x Mechanical arms 10x Standard Mounting Boards 10x Durable Storage Carrying Cases 100's other accessories

littleBits Code Kit $617.27 ex GST

Learn how to code using the Sphero littleBits Code Kit. With this coding and electronics kit, students create games and make inventions while exploring programming and engineering concepts in the classroom. Snap together the easy-to-use building blocks and start inventing. Includes 16 bits, 24 accessories, and helpful teacher resources mapped to Curriculum. Complete 100+ engaging activities and 10 lessons using the free Fuse app and littleBits Classroom. Students can work independently or in small groups of two or three per kit. New durable storage container for easy organisation and clean up. Get hands on with littleBits Code Kit today! Recommended for Grades 3+. What’s in Sphero littleBits Code Kit for Kids? 1 USB power 2 buttons 1 dimmer 1 slide dimmer 1 pressure sensor 1 sound trigger 3 wires 1 branch 1 code bit 1 bargraph 1 servo (cross axle) 1 speaker 1 round LED matrix 1 Durable Storage Case NOTE: The previous square LED matrix has been replaced by a round matrix. Some images on this page may still contain the square matrix.

littlebits code kit education class packs

littleBits Code Kit Class Pack $5,813.64 ex GST

Engage students in computational thinking by teaching them to code their own games and physical inventions in Google Blockly with a Javascript text view! Complete 100+ engaging activities and 10 lessons using the free Fuse app and littleBits Classroom. Engage 20-30 Students per Bundle 10 New durable storage containers for easy organisation and clean up. Get hands on with littleBits Code Kit today! Recommended for Grades 3+. What’s in littleBits Code Kit Class Pack? USB power x10 Buttons x10 Dimmer x10 Slide Dimmer x10 Pressure Sensor x10 Sound Trigger x10 3 Wires x10 branch x10 code bit x10 bargraph x10 servo (cross axle) x10 speaker x10 round LED matrix x10 Durable Storage x10 servo mount x10 bitShoes, hook & loop x120 mechanical arm, cross axle x10 XL mounting board, x10 USB Plug x10 microUSB Cable x10 powerSnap x30 twist ties x10 NOTE: The previous square LED matrix has been replaced by a round matrix. Some images on this page may still contain the square matrix.

littleBits STEAM Student Set - International Kit $544.55 ex GST

Meet the electronics kit designed to teach STEAM principles and encourage exploration, experimentation, and creativity through hands-on learning. Developed with educators, the STEAM Student Set makes the engineering design process fun and iterative for students while giving you everything you need to easily implement 20+ hours of standards-aligned curriculum in the classroom. Unpack the STEAM Student Set and transform students into inventors! Engage up to 3 students per kit with 19 bits and 46 accessories Run 20+ hours unplugged/no device required cross-curricular and standards-aligned lessons available on littleBits Classroom Open and guided STEAM challenges on littleBits Classroom that foster creative problem-solving skills and encourage self-expression and reflection Included Invention Guide containing Bit tips and 8 step-by-step challenges to get started Improved durable storage container for easy organisation and clean up & printed materials for instructional support and classroom implementation What’s in Sphero littleBits STEAM Student Set circuit kit? 1 power 1 USB power 1 button 1 slide dimmer 1 light sensor 1 temperature sensor 1 pulse 1 fork 2 wires 1 inverter 1 number 1 long LED 1 RGB LED 2 DC motors 1 servo & hub 1 buzzer 1 fan 1 Durable Storage Carrying Case Plus, access to littleBits classroom

littlebits steam education class pack - international

littleBits STEAM Student Set Class Pack - International $5,450.00 ex GST

Unleash student creativity with the littleBits STEAM Student Set Class Pack! Developed with educators, this electronics kit is designed to teach STEAM principles and encourage exploration, experimentation, and hands-on learning. With 10 littleBits STEAM Student Sets and 20+ hours of standards-aligned curriculum, the STEAM Student Set Class Pack enables students to practice the engineering design process in an approachable and hands-on way. Each kit serves up to 3 students and is best suited for grades 3-8. STEAM Student Set Key Features COLLABORATIVE LEARNING: Each kit contains 19 Bits and 46 accessories to engage up to 3 students and foster teamwork, communication, and collaboration skills. STANDARDS-ALIGNED: The STEAM Student Set includes 20+ hours of cross-curricular and standards-aligned lessons available on littleBits Classroom, giving educators everything they need to easily implement the kit in their classroom. Students learn fundamental concepts such as circuitry, engineering, physics, art, and design thinking. OPEN & GUIDED CHALLENGES: Find open and guided STEAM challenges on littleBits Classroom, encouraging creative problem-solving skills, self-expression, and reflection. INVENTION GUIDE: The included Invention Guide contains Bit tips and 8 step-by-step challenges to get students started. DURABLE STORAGE: The STEAM Student Set comes with individual durable storage containers for easy organisation and clean up, as well as printed materials for instructional support and classroom implementation. What's in the Bundle Power x10 USB Power x10 Button x10 Slide Dimmer x10 Light Sensor x10 Temperature Sensor x10 Pulse x10 Fork x10 Wires x10 Inverter x10 Number x10 Long LED x10 RGB LED x10 DC Motors x20 Servo & Hub x10 Buzzer x10 Fan x10 Durable Storage x10 Invention Guide Invention Log Teacher's Guide

Makerspace Invention Wall $9,086.36 ex GST

Our giant collection of nearly every Bit provides limitless options for schools and makerspaces. Access STEAM+ Coding Kit content and hours of inventions and creative builds via littleBits classroom 296 Bits Wall storage for easy Bit organization and access 3 craft packs Grades 3+ Engage 32 students NOTE: This kit is an upgrade of the Pro Library. The previous square LED matrix has been replaced by a round matrix. Some images on this page may still contain the square matrix.

littleBits Accelerometer $17.23 ex GST

Use this Bit to control your circuits with movement. The accelerometer senses how quickly you speed it up or slow it down. Snap it to a bargraph on a mounting board. Then give it a wave to visualise your movements.

littleBits Button $17.23 ex GST

The button Bit is a classic: big, round and springy for comfortable pressing! Push to turn your creation on, and release to turn it off. Snap a buzzer in place after your button to sound out signals in morse code! The button module will make or break the signal path between two modules. When the button is pressed, the output of the module is directly connected to the signal line input. When not pressed the output of the module is weakly pulled low through a 1meg resistor.

littleBits Delay $31.77 ex GST

The littleBits delay module takes incoming audio and repeats it, like an echo. It has two knobs: "time", which sets the delay length between a sound and its repetition, and "feedback", which controls how many times the sound repeats. Delays can be long and spacey, like shouting into the Grand Canyon, or loud and crazy. This Bits module will play forever if you turn up the Feedback knob all the way. [You can also shift the pitch of a sound by turning the "time" control while a sound is repeating.]

littleBits Dimmer $17.23 ex GST

Our dimmer Bit lets you control your creations with a simple knob. Turn it clockwise to send more signal to the following Bits. Try using it to control how much your vibration motor is buzzing and bouncing around.

littleBits Envelope $36.32 ex GST

The littleBits envelope modifies the loudness contour of a sound. It takes a sound input and shapes it into something you'd hear from an acoustic musical instrument, like a piano or saxophone. This envelope has two controls: "attack", which is how long it takes to ramp up to maximum volume, and "decay", which is how long it takes to go down to silence again. You can use its third bitSnap[TM] to trigger the envelope from different sources, like the keyboard. [Try it putting the envelope after an oscillator being controlled by a micro sequencer.]

littleBits Filter $32.68 ex GST

The littleBits filter has the most effect on the sound’s character or “timbre”. It affects the timbre by changing the relative volume of certain frequencies in the sound. Use it to give the impression that a sound is “brighter" (more high frequencies) or “darker” (more low frequencies.) The "cutoff" knob sets the frequency to be emphasized, and the other controls 'peak,' or intensity of the filter. If the peak is turned up all the way, the filter turns into an oscillator! [This is great for shaping all of the sounds you can make with the Synth Kit, but it's especially good with a noise input.]

littleBits Keyboard $40.86 ex GST

The keyboard lets you play melodies- it features 13 switches that make up an entire octave of notes. It has two modes: "press" (which only produces output when you press a switch) and "hold" (which will hold the last note you played). It also features an octave control which changes the playable range. In addition to its main output, which is great for controlling our oscillators, it also has a "trigger out", which you can send to the "trigger in" of envelope or other littleBits modules.

littleBits Light Sensor $25.41 ex GST

The littleBits light sensor measures how much light is shining on it. It has two modes: “light” and “dark”. In “light” mode, the more light shines on the sensor, the higher the signal it sends out. In “dark” mode, it's just the opposite – the signal increases the darker it gets. You can use a screwdriver to adjust the sensitivity. Use a bargraph to see how it's working!

littleBits Bargraph $23.59 ex GST

The bargraph is one of littleBits favourite Bits: The bargraph shows you how much signal the Bit is receiving with a display of 5 light-emitting diodes (LEDs) in different colours. Try it with a pressure sensor to make your own strength-o-meter.

littleBits Bright LED $20.86 ex GST

The littleBits bright LED (or "Light-Emitting Diode") is a small module that puts out a big light. Just like our other LED modules, it's a great way to shed some light on your creations. Choose the bright LED when you want a LOT of bright white light. The bright LED features a half watt super bright LED that responds to incoming voltages linearly. The more voltage it receives, the brighter it gets.

littleBits Buzzer $24.50 ex GST

The buzzer Bit is just what it sounds like: it makes a noise that you just can't ignore. It buzzes whenever it gets an ON signal. Try using it to make your own doorbell or alarm!

littleBits DC Motor Tethered $45.41 ex GST

The DC (or "direct current") motor rotates a small shaft you can attach anything to. Try attaching a wheel! Use it to spin, turn, twist, and roll.

littleBits Fan + Universal Mount $32.68 ex GST

The littleBits fan Bit is just what you'd think: a small electric fan tethered to a littleBits module. It's great for those hot summer nights. Use our little fan to create fluttering movement in your creations or just to keep yourself cool.

littleBits IR LED $20.86 ex GST

The littleBits IR LED (or infrared light-emitting diode) module sends out light with longer wavelengths than visible light, similar to the light in your remote control. It’s invisible to the eye, but many digital cameras can see it! Try using it to activate the light sensor or remote trigger.

littleBits LED $18.14 ex GST

The littleBits LED (or "Light-Emitting Diode") Bit is a very small board that shines a nice green light. It's our go-to when you want to light something up.

littleBits Long LED $20.86 ex GST

The littleBits long LED (or "Light-Emitting Diode") Bit is another lighting option. We call it the "long" LED because the light is tethered to the board by a cable. This lets you put the light in some interesting places: one of our favourite tricks is to place the LED in the middle of a foam ball to make it glow!

littleBits Battery + Cable $11.77 ex GST

This package contains a 9v alkaline battery and a cable to connect it to the power Bit. Connect it up and then flip the switch to power all of your creations! Note: This product is designed for use with the power Bit, and won't work with the USB or coin battery Bits!

littleBits P3 USB Power $22.68 ex GST

The USB power may be the smallest in the series, but it's big enough to send juice to all your creations. Connect a USB cable (included) to your computer or phone charger to start the power flowing. Try it with an LED to make the simplest littleBits circuit. If you're looking for a permanent installation, the USB power adapter enables you to plug your USB power directly into the wall. Using a USB connection to a computer, you have access to 500mA of power for your circuit. When using the USB Wall Adapter, you should have up to 1A of power available. The red LED shows you when the module is powered. Note: The USB power Bit does not provide a data connection.

littleBits P4 Power $12.68 ex GST

Every circuit starts with power. It uses a 9 volt battery to provide the electricity that makes your Bits spin, buzz, blink, and shine. This p4 power Bit does not include a battery.

littleBits powerSnaps $11.77 ex GST

The powerSnap supplies power to an open input without extra forks, splits, or power supplies. Includes 3 powerSnaps.

Sphero & littleBits USB Cable $11.77 ex GST

A micro USB cable for Sphero & littleBits products. Can be used for plugging into inductive chargers for Sphero SPRK+ and Sphero BOLT and is compatible with Sphero Mini. Use with littleBits by connecting a PC to your codeBit or USB power bit or for recharging your Lipo battery. The cable is approximately 0.3 meters long and comes in littleBits white. NOTE: Does not work with the Sphero RVR Battery.

littleBits Bluetooth Low Energy (BLE) $49.95 ex GST

The littleBits Bluetooth Low Energy Bit (marked "BLE" on your Bit) is the easiest way to control your inventions wirelessly, from any smart device (like a phone or tablet). All you need is the littleBits Invent app and this Bit to move motors on wireless vehicles, or trigger buzzers for pranks. You can also use your circuit to control functions on your device, like triggering the camera to take a picture.

littleBits Branch $24.50 ex GST

The Branch Bit gives you more options for connecting your littleBits: it lets you connect the output of a single Bit to as many as three others, oriented in different directions. Use it when you want to trigger light, sound and motion at the same time.

littleBits Codebit $84.50 ex GST

The codeBit levels up your littleBits circuits by allowing you to program how your Bits work. Using the littleBits Code Kit app you can command this Bit to create unique sounds, movements, and animations. The codeBit dongle allows you to wirelessly upload code from your computer to your codeBit. The USB cable brings power to your USB power Bit and rechargeable battery. It will also send information between certain Bits and your computer.

littleBits Control Voltage (CV) $68.14 ex GST

Integrate your Synth Kit with other analog synthesizers like modular synths or analog keyboards! Control littleBits module behaviours like the pitch of oscillators, the cutoff frequency of filters and more from your analog synth gear. Control analog synthesizers with littleBits modules, like a bend sensor, light sensor or any other input from the littleBits library to create new control interfaces for your synth. Sync your littleBits to other gear like Korg’s Volca series. CV stands for “control voltage” and is a widely used term in the realm of analog synthesizers. A control voltage is a variable voltage signal that is used to control module behaviors ranging from the pitch of oscillators to the cutoff setting of filters and more. The CV module can be used for both CV and Gate/Trigger type signals used in analog synthesizers. The module is suitable for interfacing with modular analog synths, analog keyboards, as well as groove boxes like the Korg Volca series. The “Sync” ports employed in the Volca series of synths can be used to make your littleBits modules play in sync with your Volcas or vice versa. The 3.5mm connection jacks should be used with mono 3.5mm plug phono cables. CV In The CV module can scale incoming voltages as high as 12V down to the 5V system the littleBits system employs. To use the CV module to control your other littleBits modules, connect the control device to the “CV In” jack. CV signals that come in through the "CV In" jack are routed to the output bitSnap™. The "CV In" jack is a switching jack so that any CVs coming in through the input bitSnap™ are not routed to the bitSnap output. When using the CV module as an input, you can control the pitch of oscillator modules, the cutoff of filter modules, trigger the envelope module, or control the speed of the micro sequencer module (put the micro sequencer into “Step” mode for this). CV Out To use the CV module to control your other CV enabled synthesizer equipment, connect the control device to the “CV Out” jack. CV signals received from littleBits modules at the input bitSnap™ are routed to the "CV Out" jack and the output bitSnap™.

littleBits Double AND $20.86 ex GST

The Double AND Bit is a logic gate with two inputs. Just like its name implies, it sends an ON signal from its output only when input one AND input two are both receiving an ON signal. The AND function can be demonstrated by thinking about a door with two locks. The only way to get through this door is to unlock lock 1 AND to unlock lock 2. Otherwise you will be stuck outside.

littleBits Double OR $20.86 ex GST

The Double OR Bit is a logic gate with two inputs. Just like its name, if input one OR input two is receiving an ON signal, then it sends an ON signal from its output. Picture a house that has a doorbell at the front door and a doorbell at the back door. Both doorbells are connected to the same buzzer inside the house. This buzzer will ring when EITHER OR BOTH of the doorbells are pressed.

littleBits Fork $22.68 ex GST

The fork Bit gives you more options for connecting your Bits: it lets you connect the output of a single Bit to as many as three others. The additional Bits will be right next to each other. Use it when you want to trigger light, sound, and motion at the same time.

littleBits Inverter $17.23 ex GST

The littleBits inverter is a very contrary logic Bit. It sends out the opposite of whatever it receives: send it an ON signal, and the inverter changes it to an OFF signal, or vice versa. Try putting it between two lights after a button: clicking will make the LEDs blink back and forth, like the lights on top of a police car! The lights on top of a police car flash back and forth. A pulse sends a signal to both of the lights, but they flash opposite one another due to the inverter.

Getting Started with littleBits $36.32 ex GST

This book is your comprehensive guide to littleBits. With dozens of curated inventions to supplement the Bit explanations, it’s perfect for beginners, educators, and anyone who wants to dive deeper into the littleBits platform and learn how to use each individual Bit.

littleBits Battery + Cable $11.77 ex GST

This package contains a 9v alkaline battery and a cable to connect it to the power Bit. Connect it up and then flip the switch to power all of your creations! Note: This product is designed for use with the power Bit, and won't work with the USB or coin battery Bits!

littleBits bitSnaps $31.77 ex GST

bitSnaps are the colour-coded, magnetic connectors found on either end of all littleBits modules. Use these to make your own modules by attaching bitSnaps to either end of your printed circuit board. They allow you to snap modules together with ease and prevent you from connecting modules the wrong way. Included in this package are 12 grey bitSnaps (6 female and 6 male connectors) and corresponding blue, pink, orange and green stickers to identify whether your new module is a power, input, wire, or output.

littleBits Brick Adapter $19.95 ex GST

The littleBits Brick Adapter enables you to easily snap littleBits modules to LEGO® bricks. Each pack comes with brick adapter studs and sockets. With brick adapter studs, your littleBits’ modules will defy gravity! Simply snap adapter underneath your bricks and press the feet of your littleBits’ modules into place. With brick adapter sockets, you can mount your littleBits’ modules on top of LEGO® bricks. Simply snap the adapter on your bricks, and press the feet of your littleBits’ modules into place. includes 8 adapters [4 studs and 4 sockets] to fit up to 24 modules littleBits modules can be adhered on top or below adapter instantly add light, sound and motion to any creation build your own LEGO® robotics or motor driven vehicle and much more LEGO is a trademark of the LEGO Group of Companies, which does not sponsor, authorise or endorse this product.

littleBits CodeBit Dongle $31.77 ex GST

The codeBit dongle allows you to wirelessly upload code from your computer to your codeBit. The USB cable brings power to your USB power Bit and rechargeable battery. It will also send information between certain Bits and your computer.

littleBits Motor Mate $11.77 ex GST

littleBits motorMate makes it easy to attach wheels, cardboard, paper and many other materials to the DC motor. Simply slide it on the “D” shape of the shaft. A LEGO™ axle also fits in the end.

littleBits Mounting Boards $31.77 ex GST

Mounting boards come 2 to a pack and allow you to keep your circuit intact and move it around with ease! Simply snap together your littleBits circuit and press the feet of your modules into the holes of the mounting board. Hold your circuit upside down, vertically, and carry it from place to place without it coming apart. Four holes in the corners allow you to permanently mount your circuit to any surface, project, or permanent installation. Mounting boards can be used individually or tiled to accommodate circuits as large as you can make. Hang it, thread it, wear it... the list goes on and on!

littleBits powerSnaps $11.77 ex GST

The powerSnap supplies power to an open input without extra forks, splits, or power supplies. Includes 3 powerSnaps.

Find anything you need

littleBits Sequencer

littleBits Sequencer

More from littleBits!

Purchase Orders Welcome

First-Class Support

Australian Warehouses

Australian Owned