littleBits Latch
$18.14 ex GST
($19.95 inc GST)
Use the littleBits latch to turn any momentary input, like a button or a trigger module, into an ON/OFF switch, like a toggle! If you place a button in front of the latch, pressing the button once will turn it ON, and pressing it again will turn it OFF again. Or for even more fun, place a sound trigger in front of the latch, and a light after it...then, just snap your fingers!
littleBits Inverter
$17.23 ex GST
($18.95 inc GST)
The littleBits inverter is a very contrary logic Bit. It sends out the opposite of whatever it receives: send it an ON signal, and the inverter changes it to an OFF signal, or vice versa. Try putting it between two lights after a button: clicking will make the LEDs blink back and forth, like the lights on top of a police car!
The lights on top of a police car flash back and forth. A pulse sends a signal to both of the lights, but they flash opposite one another due to the inverter.
littleBits Fork
$22.68 ex GST
($24.95 inc GST)
The fork Bit gives you more options for connecting your Bits: it lets you connect the output of a single Bit to as many as three others. The additional Bits will be right next to each other. Use it when you want to trigger light, sound, and motion at the same time.
littleBits P3 USB Power
$22.68 ex GST
($24.95 inc GST)
The USB power may be the smallest in the series, but it's big enough to send juice to all your creations. Connect a USB cable (included) to your computer or phone charger to start the power flowing. Try it with an LED to make the simplest littleBits circuit. If you're looking for a permanent installation, the USB power adapter enables you to plug your USB power directly into the wall. Using a USB connection to a computer, you have access to 500mA of power for your circuit. When using the USB Wall Adapter, you should have up to 1A of power available. The red LED shows you when the module is powered.
Note: The USB power Bit does not provide a data connection.
littleBits Shoes
from $19.95 ex GST
($21.95 inc GST)
Secure your circuit with our shoes! Simply snap together your littleBits circuit, press the feet of your modules into the holes of the shoes, and then place it on your chosen surface.
HOOK & LOOP Shoes come with an adhesive-backed Hook & Loop strip. The strip can be cut to any size you desire and affixed to clothing or fabric to enhance your wearable project.
ADHESIVE Shoes can be secured onto any surface -- paper, cardboard, plastic – you name it! [Adhesive backing is one-time use only.]
MAGNET shoes allow you to adhere your circuit to any magnetic surface--like your fridge!
VARIETY PACK comes with 5 Adhesive, 5 Magnet, and 5 Hook & Loop; everything you need for experimentation and building.
littleBits Mounting Boards
$31.77 ex GST
($34.95 inc GST)
Mounting boards come 2 to a pack and allow you to keep your circuit intact and move it around with ease! Simply snap together your littleBits circuit and press the feet of your modules into the holes of the mounting board.
Hold your circuit upside down, vertically, and carry it from place to place without it coming apart.
Four holes in the corners allow you to permanently mount your circuit to any surface, project, or permanent installation.
Mounting boards can be used individually or tiled to accommodate circuits as large as you can make.
Hang it, thread it, wear it... the list goes on and on!
littleBits Motor Mate
$11.77 ex GST
($12.95 inc GST)
littleBits motorMate makes it easy to attach wheels, cardboard, paper and many other materials to the DC motor. Simply slide it on the “D” shape of the shaft. A LEGO™ axle also fits in the end.
littleBits Brick Adapter
$19.95 ex GST
($21.95 inc GST)
The littleBits Brick Adapter enables you to easily snap littleBits modules to LEGO® bricks. Each pack comes with brick adapter studs and sockets. With brick adapter studs, your littleBits’ modules will defy gravity! Simply snap adapter underneath your bricks and press the feet of your littleBits’ modules into place. With brick adapter sockets, you can mount your littleBits’ modules on top of LEGO® bricks. Simply snap the adapter on your bricks, and press the feet of your littleBits’ modules into place.
includes 8 adapters [4 studs and 4 sockets] to fit up to 24 modules
littleBits modules can be adhered on top or below adapter
instantly add light, sound and motion to any creation
build your own LEGO® robotics or motor driven vehicle and much more
LEGO is a trademark of the LEGO Group of Companies, which does not sponsor, authorise or endorse this product.
littleBits Battery + Cable
$11.77 ex GST
($12.95 inc GST)
This package contains a 9v alkaline battery and a cable to connect it to the power Bit. Connect it up and then flip the switch to power all of your creations!
Note: This product is designed for use with the power Bit, and won't work with the USB or coin battery Bits!
Getting Started with littleBits
$36.32 ex GST
($39.95 inc GST)
This book is your comprehensive guide to littleBits. With dozens of curated inventions to supplement the Bit explanations, it’s perfect for beginners, educators, and anyone who wants to dive deeper into the littleBits platform and learn how to use each individual Bit.
littleBits Tackle Box
$55.00 ex GST
$90.86 ex GST ($60.50 inc GST)
$90.86 ex GST ($60.50 inc GST)
The littleBits tackle box is perfect for stowing Bits away in the workshop, or taking on the go! It has 2 levels of storage and customisable compartment sizes, thanks to the included dividers. It can store 450 Bits in up to 46 compartments.
FlashForge Guider 2-S (v2 - 2020 Model)
$2,409.09 ex GST
($2,650.00 inc GST)
This 2020 update to a solid large printer adds a flexible bed, toughen filament drive gear, toughened nozzle (included in the spare parts pack and not fitted) and improved filter. It has a user friendly touchscreen and webcam, plus a generous 280 x 250 x 300mm build volume.
All machines come standard with high-temperature extruders (to 300deg).
2020 Upgrade includes unfitted items: Magnetic self-adhesive pad, flexible steel plate, 2 sheets of build tape. Nozzle and gear kit with the hardened filament drive gear and 0.4mm nozzle, Brass 0.3, 0.4, 0.6 and 0.8mm nozzles, allen key and nozzle spanner.
The Guider 2s follows the tradition of FlashForge printers in offering an affordable, easy-to-use printer. The building volume of 280 x 250 x 300 mm is one of the largest, while the closed chamber keeps the heat in improving performance with ABS, Nylon and other materials. The printer has filament run-out detection and power failure recovery. The Flashprint software offers advanced features including internal and external dimension adjustment allowing accurate part dimensions after printing.
Features
Innovative Extruder System – completely encased air supply system to elevate printing smoothness
Heated Build Plate – supports multiple mainstream filament types for diverse printing needs
Touch Screen – Guider IIs is equipped with a 5-inch full-colour touch screen and multilingual user interface.
Built-in Air Filter
HD Camera to monitor the print any time
Specifications
Nozzle Diameter (mm)
0.4 mm
Build Volume W x D x H (mm)
280 x 250 x 300 mm
Printing Technology
FFF
Proprietary filament
Yes, also compatible with others
Filament Diameter (mm)
1.75 mm
Material type
PLA / ABS / Flexible
Heated Bed
Yes
Build Plate
Glass with Buildtak
Layer Thickness (microns)
50 - 350 microns
Platform Levelling
Assisted
Connectivity
USB, WiFi, Ethernet
Slicing Software
Flashprint, Slic3r, Cura
File Input Format
STL, OBJ
Power Supply
100-240 V, 50-60 Hz, 500 W
Software Compatibility
Windows 7, Mac OS X
XY Positioning Accuracy
11 microns
Warranty
12 months
FlashForge Hunter - Resin Printer
$4,636.36 ex GST
($5,100.00 inc GST)
This high quality resin printer is designed for applications where very high resolution is essential, such as jewelry and dentistry.
Build size is 120 x 67.5 x 150mm
Print Technology: DLP
5 inch Touchscreen
Build Size: 120 x 67.5 x 150mm
Print Precision: ± 0.05mm
Pixel Size X, Y: 0.0625mm (62.5microns)
Light Source: 405nm LED, FHD 1080p resolution with 50,000 hours lifespan
Layer Thickness: 0.05 / 0.025 / 0.0125mm (50 / 25 / 12.5 microns)
Speed: 10mm/h (vertical)
Vat Type: Aluminium with replaceable FEP film
Processor Type: Dual-core 800MHz ARM
Machine Size: 360 x 310 x 565mm
Machine Weight: 17.8kg
Power Input: 100-240V, 50-60Hz, 1A
Connection: USB Flash Drive, USB Cable or WiFi
Software: FlashPrint. Free download for Win XP-10, Mac OS, Linux
File Input Format: .stl
Dimensions: 360 x 310 x 565mmFormat: 3D Printer
FlashForge AD1 - Sign Lettering 3D Printer
$7,271.82 ex GST
($7,999.00 inc GST)
Part of the FlashForge Professional range, this 3D Printer is designed to be a complete solution for printing Light Channels for Signage
The special slicing & designing software, FlashAD, makes it easier to make complex designs, you can even create an amazing shadow effect with returned slant at some angles as you wish, eliminating the trouble of calculating the curving angle in CNC machining. Strongly helps you to fabricate complicated logos easily.NOTE: This machine is designed for commercial use only. It comes on an oversized pallet in a wooden crate. You will have to carefully turn it on its side to get it through a standard doorway. Thankfully the crate is sturdy and the machine is bolted inside.
Features- Resume printing after power outage- Filament detetion- Screensaver function- Printed file identification (turns green in file list)Printing- Single Nozzle, 2 filament colours (2in / 1 out)- Build Volume: 600 x 600 x 70mm- Layer Heights 0.2 - 0.4mm- Print Resolution: ± 0.5mm or 0.2%- Print Speed: 10-80mm/s- Nozzle Diameter: 0.6mm - Maximum Nozzle Temperature: 260°C- Heated Build Plate: to 100°C- Leveling: 8 point, manual- Material: A-PLA recommendedMachine- 4.5 Inch Touchscreen- 8Gb Onboard Memory- Power: 220VAC, 47-63Hz, 1500W- Machine Weight: 50.2kg- Machine Size: 1170x975x485mmCommunication- Software: FlashAD - Windows 32bit and 64bit- Data Transmission: USB Drive, Ethernet, FlashCloud. Note: No WiFi.- File Output: GFZ- File Input Types: FAD, STL, NC, CDRDimensions: 1070 x 975 x 485mm
Roadcase for the Inventor 2/SE or Finder
$908.18 ex GST
($999.00 inc GST)
This flight ready, rugged road case is designed to neatly store your Flashforge Finder, Inventor 2 or Special Edition 3D Printer, with a rear storage section for Filament, spare parts and power supply. It is on lockable casters for easy moving.
Main section holds your machine safe with slots in the padding so you can lift it out by the side handles on the machine with minimum effort.
The rear storage section has space for 4 spools of filament, toolbox, spare parts and power supply.
This quality roadcase is on lockable casters for easy moving and the machine can be safely operated on top of the closed lid.Internal Size
43 wide, 45 deep, 44cm TallRear storage area 15 cm deepExternal Size
709 wide, 558 deep, 663cm (including casters) TallRear storage area 15 cm deepCasters: Locakble 80mm heavy dutyHinged LidHigh density foam linedWith printer + filament and a tool kit this case weights 45KgDimensions: Internal 43x45x44cm with 15cm rear compartment
Roller Spool Stand - 140mm wide
$25.45 ex GST
($28.00 inc GST)
Bilby 3D designed and 3D printed spool stand for 114mm wide spools.
Our 2020 design is bigger and stronger. It accommodates our 3kg spools, but will also carry our 1kg and 600g spools.
This is the roller stand only. If you need to use a feeder tube, maybe the filament path goes around corners or could get snagged, please purchase the correct length separately.
Dimensions: 195 x 150 x 55mm
ClassVR Controllers - 8 Pack
$271.82 ex GST
($299.00 inc GST)
Being powered solely by the ClassVR headset during use, it’s lightweight and features three buttons, plus a central joystick controller.When immersing students into a virtual learning environment with ClassVR headsets, the optional Controller empowers students to intuitively explore their virtual environment with a new found fluidity and complete control.
ClassVR Cube (Set of 8)
$108.18 ex GST
($119.00 inc GST)
The ClassVR Cube for augmented reality, allows you to observe and rotate the 3D model displayed through the ClassVR viewers.
ClassVR Online CPD Portal
$508.00 ex GST
($558.80 inc GST)
The ClassVR online course has been designed to help you get the most from your investment. The course consists of comprehensive, bite-sized lectures – with short videos and quizzes, which allows you to learn at your own convenience.
You can re-visit the course at any time, allowing you to refresh your memory or sharpen your skills.
What’s Included?
Each course consists of focused lectures to step through in your own time,including:
Bite-size videos that cover the topic in-depth
Downloadable supporting documents for reference
Quick quizzes to test your knowledge
You’ll receive updates as we add more material to our online courses, so you can stay up to date with the latest features.
Eduverse School Licence
from $1,190.00 ex GST
($1,309.00 inc GST)
ClassVR is Powered by Eduverse
Eduverse is the content library behind ClassVR offering hundreds of thousands of curriculum-aligned immersive experiences across every subject. Teachers can launch and manage lessons easily through the intuitive ClassVR Portal.
In order to access the expansive range of content that is available for you ClassVR headsets, you will need to purchase a subscription.
Subscriptions can be purchased in blocks of 1, 3 or 5 years. Your subscription provides you access to all Eduverse content, ClassVR content and associated teacher resources as well as the ability to upload your own content and the classroom management tools to deliver it to students.
What is Eduverse?
Eduverse is a revolutionary online learning environment providing a safe and secure ‘metaverse’ for K-12 schools.
Eduverse allows you and your students to harness the power of the metaverse and explore immersive virtual worlds in a safe and inclusive environment. Eduverse offers a new way to learn, enabling students to collaborate in engaging virtual spaces where the impossible becomes a reality.
What can you do in the Eduverse?
The Eduverse powers all of our educational VR products. From one single login you can access Expeditions, Avantis World and experience the Eduverse using ClassVR.
HoverCam Solo 8 Plus Document Camera
$699.00 ex GST
$745.45 ex GST ($768.90 inc GST)
$745.45 ex GST ($768.90 inc GST)
Elevate your teaching and presentations with the HoverCam Solo 8 Plus Document Camera, a revolutionary tool designed to enhance distance learning and in-class instruction. Experience True 4K Image Clarity with its 13 Megapixel Sensor, capturing every detail with ease. This document camera is equipped with a single USB cable connection—no power adapters required—making it incredibly easy to use and set up.
Key Features
True 4K Image Clarity: Capture stunning, high-resolution images and videos for flawless presentations and lectures.
ASR Zoom Technology: Enjoy lossless zoom with our Adaptive Sensor Resolution, providing 480x zoom without compromising image quality.
Flex 11 Software Integration: Leverage powerful features like annotation, lesson recording, and a built-in virtual whiteboard, enhancing interactivity and engagement.
Compatibility with Leading Platforms: Seamlessly works with Zoom, Skype, Google Hangouts, and more, offering better image quality and versatility than a standard webcam.
OCR Scanner & PDF Capability: Effortlessly scan documents into PDF format, saving time and preserving quality.
Additional Benefits
Built-in Microphone: Capture high-quality audio alongside your video recordings, perfect for complete lesson delivery.
Interactive Whiteboard Integration: Works with leading interactive whiteboard packages like SMART Notebook and Promethean.
Motion Sensor Photography: Includes innovative features like time-lapse and slow-motion video recording.
First-Class Support: Get exceptional support from our team of former educators who understand your needs.
Australian Owned and Operated: Enjoy efficient delivery from our Australian warehouses with true Aussie spirit.
Purchase Orders Welcome: Schools and educational institutions can take advantage of our seamless purchasing process with purchase order options at checkout.
HoverCam Solo Series Microscope Adapter
$40.86 ex GST
($44.95 inc GST)
The HoverCam Solo Series Microscope Adapter allows you to utilize your Solo 5 or 8 HoverCam with any standard monocular microscope. Display minuscule objects to the entire class with the HoverCam you already use. Take advantage of HoverCam Flex software features, like video and audio recording, scanning to PDF, and interactive whiteboard integration. Exclusively for use with the HoverCam Solo 5 or 8 document camera.
Lightning to USB Connector Cables
from $119.00 ex GST
($130.90 inc GST)
Designed for iPad, iPad Air, iPad mini and other iOS devices with the lightning connection.
The MFi Approved Lightning Cables come in either 300mm or 1200mm in length making them perfect for coupling with the PC Locs iQ Range.
Pack of 5 cables.
Redcat Soft Carry Case
$245.00 ex GST
($269.50 inc GST)
This custom-designed carry case allows you to take your Redcat Access outside of the school.
PowerMount for Redcat
$81.82 ex GST
($90.00 inc GST)
Designed for installing the Redcat or Redcat Access on a wall with space to hold the power supply.
Dimensions:
Length x Height x Depth:30.48 x 3.81 x 4.45cm
Weight:272 g
1 Pair Feet Redcat Table Stand
$23.00 ex GST
($25.30 inc GST)
Additional accessories in case you move your systems around the school, available to purchase separately for Redcat Access and Redcat Infra-Red.
Redcat Access Battery Compartment Cover
$23.00 ex GST
($25.30 inc GST)
The RCA Battery Compartment Cover is available for Redcat Access system. This cover is to be used if you take your Lithium Battery out of Redcat Access speaker unit.
Lithium batteries are available to purchase from us separately to make your Redcat Access system portable and for outdoor use.
Lightmike LT71 Battery
$20.00 ex GST
($22.00 inc GST)
Although the LT71 Lightmike has been discontinued, we continue to stock batteries for this product.
Access Customer Care Kit
$843.00 ex GST
($927.30 inc GST)
This kit is designed for schools that would like to have Redcat Access audio system spare parts handy before anything goes wrong. Handy for quick fixes and when you need it most. Please contact us to find out which parts are included in this kit.
Redcat Access Rechargeable Battery Pack
$350.00 ex GST
($385.00 inc GST)
If you would like your Redcat sound system to be portable and wireless, this battery will give you the flexibility to take your system outside of your classroom (works only with latest generation of Redcat Access).
Lithium Ion Rechargeable Battery Pack
The L14V Lithium Ion (Li-Ion) rechargeable battery is built for the Redcat Access Classroom Audio Systems. Redcat Access system's purchased after June 1, 2016, have a door on the back of the system that can be removed to house this new battery. Charging is accomplished by the use of the 24V 1.75v power supply that accompanies all Redcat Access systems. Battery life is 12 hours on a single charge.
Redcat Access Rechargeable Battery
Type
lithiumIon
Charge Protection
Yes
Capacity
2800mAH
Charge
14.8V
Dimensions
155.8mm x 94mm x 19mm Weight: 283.5g
Redcat Infra-Red RC2 Power Supply
$120.00 ex GST
($132.00 inc GST)
Replace your lost or damaged power supply for Redcat Infra-Red only.
