Use the littleBits latch to turn any momentary input, like a button or a trigger module, into an ON/OFF switch, like a toggle! If you place a button in front of the latch, pressing the button once will turn it ON, and pressing it again will turn it OFF again. Or for even more fun, place a sound trigger in front of the latch, and a light after it...then, just snap your fingers!

The littleBits inverter is a very contrary logic Bit. It sends out the opposite of whatever it receives: send it an ON signal, and the inverter changes it to an OFF signal, or vice versa. Try putting it between two lights after a button: clicking will make the LEDs blink back and forth, like the lights on top of a police car! The lights on top of a police car flash back and forth. A pulse sends a signal to both of the lights, but they flash opposite one another due to the inverter.

The fork Bit gives you more options for connecting your Bits: it lets you connect the output of a single Bit to as many as three others. The additional Bits will be right next to each other. Use it when you want to trigger light, sound, and motion at the same time.

The USB power may be the smallest in the series, but it's big enough to send juice to all your creations. Connect a USB cable (included) to your computer or phone charger to start the power flowing. Try it with an LED to make the simplest littleBits circuit. If you're looking for a permanent installation, the USB power adapter enables you to plug your USB power directly into the wall. Using a USB connection to a computer, you have access to 500mA of power for your circuit. When using the USB Wall Adapter, you should have up to 1A of power available. The red LED shows you when the module is powered. Note: The USB power Bit does not provide a data connection.

Secure your circuit with our shoes! Simply snap together your littleBits circuit, press the feet of your modules into the holes of the shoes, and then place it on your chosen surface. HOOK & LOOP Shoes come with an adhesive-backed Hook & Loop strip. The strip can be cut to any size you desire and affixed to clothing or fabric to enhance your wearable project. ADHESIVE Shoes can be secured onto any surface -- paper, cardboard, plastic – you name it! [Adhesive backing is one-time use only.] MAGNET shoes allow you to adhere your circuit to any magnetic surface--like your fridge! VARIETY PACK comes with 5 Adhesive, 5 Magnet, and 5 Hook & Loop; everything you need for experimentation and building.

Mounting boards come 2 to a pack and allow you to keep your circuit intact and move it around with ease! Simply snap together your littleBits circuit and press the feet of your modules into the holes of the mounting board. Hold your circuit upside down, vertically, and carry it from place to place without it coming apart. Four holes in the corners allow you to permanently mount your circuit to any surface, project, or permanent installation. Mounting boards can be used individually or tiled to accommodate circuits as large as you can make. Hang it, thread it, wear it... the list goes on and on!

littleBits motorMate makes it easy to attach wheels, cardboard, paper and many other materials to the DC motor. Simply slide it on the “D” shape of the shaft. A LEGO™ axle also fits in the end.

The littleBits Brick Adapter enables you to easily snap littleBits modules to LEGO® bricks. Each pack comes with brick adapter studs and sockets. With brick adapter studs, your littleBits’ modules will defy gravity! Simply snap adapter underneath your bricks and press the feet of your littleBits’ modules into place. With brick adapter sockets, you can mount your littleBits’ modules on top of LEGO® bricks. Simply snap the adapter on your bricks, and press the feet of your littleBits’ modules into place. includes 8 adapters [4 studs and 4 sockets] to fit up to 24 modules littleBits modules can be adhered on top or below adapter instantly add light, sound and motion to any creation build your own LEGO® robotics or motor driven vehicle and much more LEGO is a trademark of the LEGO Group of Companies, which does not sponsor, authorise or endorse this product.

This package contains a 9v alkaline battery and a cable to connect it to the power Bit. Connect it up and then flip the switch to power all of your creations! Note: This product is designed for use with the power Bit, and won't work with the USB or coin battery Bits!

This book is your comprehensive guide to littleBits. With dozens of curated inventions to supplement the Bit explanations, it’s perfect for beginners, educators, and anyone who wants to dive deeper into the littleBits platform and learn how to use each individual Bit.

The littleBits tackle box is perfect for stowing Bits away in the workshop, or taking on the go! It has 2 levels of storage and customisable compartment sizes, thanks to the included dividers. It can store 450 Bits in up to 46 compartments.